 |
|
The 2-way full range system shall incorporate a 5.25 inch magnetically shielded low frequency transducer and a 1.0 inch neodymium tweeter mounted to a rectangular horn flare horn flare. The full range system’s low frequency drivers shall be loaded into a ported enclosure.
The full range system shall meet the following performance criteria: frequency response of 75 Hz to 19.0 kHz ±6 dB, measured on axis with appropriate signal processing; sensitivity of 86.5 dB SPL in free field at 1 meter with an input of 2.83V; continuous output of 104.0 dB SPL; peak output of 110.0 dB SPL on axis at 1 meter; power handling of 60 watts for 8 hours with an IEC noise signal; recommended amplifier power of 120 watts; nominal impedance of 8 ohms. The full range system's nominal coverage between -6 dB points shall be 90 degrees in one plane and 90 degrees in the orthogonal plane.
The loudspeaker shall have an low-distortion, wide-bandwidth laminated core transformer with taps for watts at 70V and watts at 100V.
The loudspeaker shall have a weather-resistant enclosure constructed of injection molded high impact polystyrene. It shall have a black or white paintable finish. Input connectors shall be parallel wired 5-way binding posts. The full range system shall have a removable ball mount adapter and an optional yoke mount. The front of the full range system shall be protected by a a heavy duty powder coated aluminum grill.
The full range system's enclosure shall be 11.28 in (28.65 cm) high, 7.02 in (17.83 cm) wide and 9.33 in (21.16 cm) deep. The loudspeaker shall weigh no more than 15.0 lb (6.8 kg).
The 2-way full range system shall be the QSC Audio Products AD-S52.
The 2-way full range system shall incorporate a 5.25 inch magnetically shielded low frequency transducer and a 1.0 inch neodymium tweeter mounted to a rectangular horn flare horn flare. The full range system’s low frequency drivers shall be loaded into a ported enclosure.
The full range system shall meet the following performance criteria: frequency response of 75 Hz to 19.0 kHz ±6 dB, measured on axis with appropriate signal processing; sensitivity of 86.0 dB SPL in free field at 1 meter with an input of 2.83V; continuous output of 101.0 dB SPL; peak output of 107.0 dB SPL on axis at 1 meter; power handling of 100 watts for 8 hours with an IEC noise signal; recommended amplifier power of 200 watts; nominal impedance of 8 ohms. The full range system's nominal coverage between -6 dB points shall be 90 degrees in one plane and 90 degrees in the orthogonal plane.
The loudspeaker shall have an internal low-distortion, wide-bandwidth laminated core transformer with taps for 30, 15, 7.5 & 3.75 watts at 70V and 30, 15 & 7.5 watts at 100V.
The loudspeaker shall have a weather-resistant enclosure constructed of injection molded high impact polystyrene. It shall have a black or white paintable finish. Input connectors shall be parallel wired 5-way binding posts. The full range system shall have a removable ball mount adapter and an optional yoke mount. The front of the full range system shall be protected by a a heavy duty powder coated aluminum grill.
The full range system's enclosure shall be 11.28 in (28.65 cm) high, 7.02 in (17.83 cm) wide and 9.33 in (21.16 cm) deep. The loudspeaker shall weigh no more than 18.0 lb (8.2 kg).
The 2-way full range system shall be the QSC Audio Products AD-S52T.
The 2-way full range system shall incorporate a 8.0 inch low frequency transducer and a 1.0 inch titanium dome tweeter with a neodymium magnet mounted to an Advanced Directivity horn flare. The HF horn shall be capable of being rotated to accommodate horizontal or vertical installation. The full range system’s low frequency drivers shall be loaded into a ported enclosure.
The full range system shall meet the following performance criteria: frequency response of 85 Hz to 18.0 kHz ±6 dB, measured on axis with appropriate signal processing; sensitivity of 90.5 dB SPL in free field at 1 meter with an input of 2.83V; continuous output of 111.0 dB SPL; peak output of 117.0 dB SPL on axis at 1 meter; power handling of 90 watts for 8 hours with an IEC noise signal; recommended amplifier power of 180 watts; nominal impedance of 8 ohms. The loudspeaker shall have built-in dynamic full range power protection circuitry, activated by signal overload conditions. The full range system's nominal coverage between -6 dB points shall be 90 degrees in one plane and 60 degrees in the orthogonal plane.
The loudspeaker shall have an optional low-distortion, wide-bandwidth laminated core transformer with taps for 60, 30, 15 & 7.5 watts at 70V and 60, 30 & 15 watts at 100V. The transformer shall be integrated into the IntelliDock mounting system or the optional yoke mount.
The loudspeaker shall have a weather-resistant enclosure constructed of injection molded high impact polystyrene. It shall have a black or white paintable finish. The full range system shall have an integrated IntelliDock mounting system incorporating electrical connections, mechanical mounting and security provisions. Input connectors shall be parallel wired 5-way binding posts, concealed within the IntelliDock mounting system. A yoke mount shall be available as an option. The front of the full range system shall be protected by a a heavy duty powder coated aluminum grill.
The full range system's enclosure shall be 17.73 in (44.09 cm) high, 10.03 in (25.48 cm) wide and 11.22 in (28.5 cm) deep. The loudspeaker shall weigh no more than 16.9 lb (7.7 kg).
The 2-way full range system shall be the QSC Audio Products AD-S82.
The 2-way full range system shall incorporate a 8.0 inch low frequency transducer with a2.0 inch voice coil, and a 1.0 inch high output compression driver mounted to an Advanced Directivity horn flare. The HF horn shall be capable of being rotated to accommodate horizontal or vertical installation. The full range system’s low frequency drivers shall be loaded into a ported enclosure.
The full range system shall meet the following performance criteria: frequency response of 80 Hz to 21.0 kHz ±6 dB, measured on axis with appropriate signal processing; sensitivity of 90.5 dB SPL in free field at 1 meter with an input of 2.83V; continuous output of 114.0 dB SPL; peak output of 120.0 dB SPL on axis at 1 meter; power handling of 200 watts for 8 hours with an IEC noise signal; recommended amplifier power of 400 watts; nominal impedance of 8 ohms. The loudspeaker shall have built-in dynamic full range power protection circuitry, activated by signal overload conditions. The full range system's nominal coverage between -6 dB points shall be 90 degrees in one plane and 60 degrees in the orthogonal plane.
The loudspeaker shall have an optional low-distortion, wide-bandwidth laminated core transformer with taps for 60, 30, 15 & 7.5 watts at 70V and 60, 30 & 15 watts at 100V. The transformer shall be integrated into the IntelliDock mounting system or the optional yoke mount.
The loudspeaker shall have a weather-resistant enclosure constructed of injection molded high impact polystyrene. It shall have a black or white paintable finish. The full range system shall have an integrated IntelliDock mounting system incorporating electrical connections, mechanical mounting and security provisions. Input connectors shall be parallel wired 5-way binding posts, concealed within the IntelliDock mounting system. A yoke mount shall be available as an option. The front of the full range system shall be protected by a a heavy duty powder coated aluminum grill.
The full range system's enclosure shall be 17.73 in (44.09 cm) high, 10.03 in (25.48 cm) wide and 11.22 in (28.5 cm) deep. The loudspeaker shall weigh no more than 16.9 lb (7.7 kg).
The 2-way full range system shall be the QSC Audio Products AD-S82H.
The 2-way full range system shall incorporate dual 8.0 inch low frequency transducers with 2.0 inch voice coils, and a 1.0 inch high output compression driver mounted to an Advanced Directivity horn flare. The HF horn shall be capable of being rotated to accommodate horizontal or vertical installation. The full range system’s low frequency drivers shall be loaded into a ported enclosure. The full range system shall have a passive internal crossover network with switchable full range or bi-amped operation.
The full range system shall meet the following performance criteria: frequency response of 80 Hz to 27.0 kHz ±6 dB, measured on axis with appropriate signal processing; sensitivity of 93.0 dB SPL in free field at 1 meter with an input of 2.83V; continuous output of 119.0 dB SPL; peak output of 125.0 dB SPL on axis at 1 meter; power handling of 450 watts for 8 hours with an IEC noise signal; recommended amplifier power of 900 watts; nominal impedance of 8 ohms. The full range system's nominal coverage between -6 dB points shall be 90 degrees in one plane and 60 degrees in the orthogonal plane.
The loudspeaker shall have a weather-resistant enclosure constructed of injection molded high impact polystyrene. It shall have a black or white paintable finish. Input connectors shall be parallel wired barrier strips with passive/active switching. A yoke mount shall be available as an option. The front of the full range system shall be protected by a a heavy duty powder coated aluminum grill.
The full range system's enclosure shall be 26.17 in (66.5 cm) high, 10.21 in (25.9 cm) wide and 11.44 in (29.0 cm) deep. The loudspeaker shall weigh no more than 27.7 lb (12.6 kg).
The 2-way full range system shall be the QSC Audio Products AD-S282H.
The 2-way full range system shall incorporate dual 8.0 inch low frequency transducers with 2.0 inch voice coils, and a 1.0 inch high output compression driver mounted to an Advanced Directivity horn flare. The HF horn shall be capable of being rotated to accommodate horizontal or vertical installation. The full range system’s low frequency drivers shall be loaded into a ported, 60 Hz tuned enclosure.
The full range system shall meet the following performance criteria: frequency response of 80 Hz to 27.0 kHz ±6 dB, measured on axis with appropriate signal processing; sensitivity of 93.0 dB SPL in free field at 1 meter with an input of 2.83V; continuous output of 119.0 dB SPL; peak output of 125.0 dB SPL on axis at 1 meter; power handling of 450 watts for 8 hours with an IEC noise signal; recommended amplifier power of 900 watts; nominal impedance of 8 ohms. The full range system's nominal coverage between -6 dB points shall be 90 degrees in one plane and 60 degrees in the orthogonal plane.
The loudspeaker shall have an switchable low-distortion, wide-bandwidth laminated core transformer with taps for 200, 100, 50 & 25 watts at 70V and 200, 100 & 50 watts at 100V. The full range system shall be switchable between 8 Ohm and constant-voltage operation.
The loudspeaker shall have a weather-resistant enclosure constructed of injection molded high impact polystyrene. It shall have a black or white paintable finish. Input connectors shall be parallel wired barrier strips. A yoke mount shall be available as an option. The front of the full range system shall be protected by a a heavy duty powder coated aluminum grill.
The full range system's enclosure shall be 26.17 in (66.5 cm) high, 10.21 in (25.9 cm) wide and 11.44 in (29.0 cm) deep. The loudspeaker shall weigh no more than 27.7 lb (12.6 kg).
The 2-way full range system shall be the QSC Audio Products AD-S282HT.
QSC and the QSC logo are registered trademarks of QSC Audio Products, LLC in the U.S. Patent and Trademark office and other countries. All other trademarks are the property of their respective owners. Patents may apply or be pending.
|