| ILA Series |
 |
 |
| SPECIFICATIONS |
WL2082-i |
WL115-sw |
| Configuration |
2 1/2 way, Bi-amp or Tri-amp |
4th order bandpass subwoofer |
Transducers
High Frequency
Low Frequency |
Dual 50 W, 8 ohm 1" exit, 1.75" titanium diaphragm, neodymium magnet assembly
Dual 200 W, 16 ohm 8" woofers, 2" voice coils, neodymium magnet assemblies, weather resistant cone
|
--
650 W, 8 ohm 15" woofer with 4" voice coil, ceramic magnetic assembly |
Frequency Response (±3 dB)
Frequency Range (-10 dB) |
80 Hz - 20 kHz
68 Hz - 22 kHz |
37 Hz - 107 Hz
35 Hz - 112 Hz |
| Nominal Impedance |
HF: 16 ohms
LF bi-amp mode: 8 ohms
LF tri-amp mode: 16 ohms (x2) |
LF:
8 ohms |
| Sensitivity (1 W @ 1 m) |
HF: 106 dB
LF: 97 dB
|
96 dB |
Continuous Power Capacity 1
|
HF: 100 W
LF bi-amp mode: 400 W
LF tri-amp mode: 200 W (x2)
|
LF: 650 W RMS |
| Recommended Power |
HF: 200 W
LF bi-amp mode: 800 W
LF tri-amp mode: 400 W (x2) |
LF: 1300 W RMS |
Maximum Output (dB SPL at 1 m)
Continuous / Peak |
HF: 126 dB / 132 dB
LF: 122 dB / 128 dB
|
LF: 124 dB / 130 dB
|
| Nominal Coverage |
Horizontal 140 degrees
Vertical: dependent on number of elements used |
|
| Cabinet Type |
Ported, elliptical / trapezoidal |
4th order bandpass |
| Enclosure Material |
HIPS (high impact polystyrene) with UV protectant |
18 mm Baltic Birch Plywood |
| Finish |
Available in black (WL2082-i BLK) or white (WL2082-i WHT) paintable |
Available in black (WL115-sw BLK) or white (WL115-sw WHT) paintable |
| Grille |
Perforated, formed aluminum |
|
| Connectors |
2 x NL-8 in parallel |
2 x NL-8 in parallel |
| Pin Outs |
| Pins |
Bi-amp |
Tri-amp |
| 1+/1- |
NC |
NC |
| 2+/2- |
NC |
LF2 |
| 3+/3- |
LF |
LF1 |
| 4+/4- |
HF |
HF |
|
| Pins |
|
| 1+/1- |
Sub |
| 2+/2- |
NC |
| 3+/3- |
NC |
| 4+/4- |
NC |
|
| Attachment Points |
Integral, side plate adjustable rigging system, vertical splay adjustable in 1° increments from 0° - 10° |
Integral, non-adjustable (straight array only) |
| Dimensions |
11.8" H x 27" W x 13.4" D
(300 mm x 686 mm x 340 mm) |
22.1" H x 27 " W x 30.25" D
(561 mm x 686 mm x 768 mm) |
| Weight |
37 lbs (16.8 kg) net
45 lbs (20.45 kg) shipping |
111 lbs (50.4 kg) net
121 lbs (55 kg) shipping |
| Accessories Available |
FB2082-i: Fly-bar for WL2082-i and WL115-sw.
Available in black or white.
EB2082-i: Extension bar, allows WL115-sw to be suspended behind WL2082-i. (52" long. When attached to 2 fly grids, it adds 3" for a total of 55") Available in black or white.
PB2082-i: Pullback bar for WL2082-i. For use when pulling back the bottom of the array is necessary to achieve the desired angle.
Available in black or white.
QRP-KIT-1: Kit of four (4) Quick Release Pins for use in lieu of included bolts. |
